7 AutoCAD Tutors Found Near Charleston, SC



Photo: Cecilia C.

Cecilia C.

AutoCAD Tutor

Charlotte, NC 28210

Will travel 10 miles

$70 per hour.

4.75 4 ratings

View Cecilia C.

Experience Architect and Professor

I use AutoCAD 2015 on a daily basis in my part time job. I work at RAM Design, in Sunrise. What I do there is to draft all their projects (residential and commercial creating a full set of construction documents in AutoCAD). I am an architect with a Master in Architecture degree from Oklahoma State University. I have more than 25 years experience practicing architecture in different countries. I have taught design and graphics for 12 years in three different Universities: 5 years at Universidad Jose Antonio Paez in Valencia-Venezuela, 4 years at University of South Florida in Tampa-Florida [more]


Photo: Rafael B.

Rafael B.

AutoCAD Tutor

Augusta, GA 30909

Will travel 20 miles

$40 per hour.

0.0 0 ratings

View Rafael B.

CAD/BIM Instructor

I have an architecture drafting certificate from a college. I did at least 60 college hours in AutoCad training and have been using it since 2005. I am formally trained in AutoCAD and received my Architectural drafting certification in 2007. I went on to Architecture school and received my bachelors in 2013. I have been using AutoCAD since 2005 and Revit since 2012. I am self employed and do high end residential architecture. I am also capable of using Adobe Suite. I am self employed and have a pretty flexible schedule. I can usually accommodate hours without much notice.... [more]


Photo: Christopher C.

Christopher C.

AutoCAD Tutor

Aiken, SC 29803

Will travel 20 miles

$20 per hour.

0.0 0 ratings

View Christopher C.

CAD Tutor available / 20 years experience in varying fields

I have 18+ years of AutoCAD experience starting with AutoCAD R12 to AutoCAD 2015. I also taught board drafters AutoCAD for a company I worked for. I was then asked to develop an AutoCAD drafting program for the company and then to oversee software development projects for the same company. I have 18+ years of CAD experience in the industrial, manufacturing, non-destructive testing, medical, security electronics, and construction (commercial and residential) fields. Also, I served as an AutoCAD trainer for one of my former companies and went on to become an IT Project manager overseeing soft [more]


Photo: Jackie P.

Jackie P.

AutoCAD Tutor

Lavonia, GA 30553

Will travel 30 miles

$40 per hour.

4.0 7 ratings

View Jackie P.

Engineer - *Math*

I am a civil engineer. I have been trained in and worked using AutoCAD from R-12 to Civil 3-D 2008. I used AutoCAD on a daily basis for 7 years. I love math. I hold a Bachelor's degree in Civil Engineering from Clemson University. I am patient and have a way of explaining math (and other things) that enable students to understand and therefore master the math! I am also good with reading and writing. I have a knack with writing, from short stories, essays and term papers to technical writing skills. I was also a physical education major at James Madison University in years past. At J [more]


Photo: Brian P.

Brian P.

AutoCAD Tutor

East Flat Rock, NC 28726

Will travel 35 miles

$35 per hour.

0.0 0 ratings

View Brian P.

Skilled CAD Specialist Offering 2D/3D Drafting Tutoring Services

I have four years of recent experience using AutoCAD and similar programs. I spent two years at Eaton Corporation in the Low Voltage Switch Gear department and two years as a junior engineer at Linamar NC. My expertise includes Auto Desk's Inventor 3D software. I'm a highly motivated engineer who specializes in 2D and 3D Computer Aided Drafting and it's related programs and processes. I have just over four years of recent experience in the manufacturing industry and nearly ten years spent in electrical engineering. Over my career I've become knowledgeable in quite a few areas including electri [more]


Photo: Kevin I.

Kevin I.

AutoCAD Tutor

Kings Mountain, NC 28086

Will travel 10 miles

$50 per hour.

0.0 0 ratings

View Kevin I.

25+ years AutoCAD, Solid Modeling (Inventor) and Computer Engineering

I have used AutoCAD for over 25 years in doing mechanical design. I have 12 years of engineering experience with industrial products. I have taught several levels of drafting including AutoCAD at high school and community college for the last eight years. My name is Kevin and I am available for tutoring in AutoCAD and Autodesk Inventor. I have used CAD and solid modeling for over twenty years including working as a design engineer with various electro-mechanical products and then teaching at both the high school and community college levels. I have taught many levels of drafting, including [more]


Photo: Charles B.

Charles B.

AutoCAD Tutor

Columbia, SC 29212

Will travel 30 miles

$58 per hour.

3.67 3 ratings

View Charles B.

Engineer, Mathematician, & Physicist

I am a Registered Professional Engineer involved with foundation design and design of retaining walls using AutoCAD. I am a certified AutoCAD user and have produced many engineering drawings from manufactured products to land development design and supporting details using AutoCAD. My professional experience includes Senior Design Engineer/Principal where I provide civil/structural design, hydraulic design and drafting support for land development projects; conduct environmental site assessments/jurisdictional wetlands delineations; conduct asbestos inspections; analyze geotechnical condition [more]