8 Mechanical Engineering Tutors Found Near Hartford, CT



Photo: Dave D.

Dave D.

Mechanical Engineering Tutor

South Hadley, MA 01075

Will travel 40 miles

$50 per hour.

4.81 349 ratings

View Dave D.

Math and Physics Tutor

Before I chose my original college route of becoming a math major for my first degree at SUNY at Stonybrook, I originally completed the first two years of undergraduate Mechanical Engineering Classes at a community college and was accepted into Stonybrook University as a 3rd year Mechanical Engineer. Once I became enrolled there, I switched my interest to a straight mathematics degree. I originally liked math much more than physics. It wasn't until I went back to school many years later at Boston University did I pursue my interest in Physics. All the same, because of this I have taken and don [more]


Photo: Jamie D.

Jamie D.

Mechanical Engineering Tutor

Fairfield, CT 06824

Will travel 10 miles

$90 per hour.

0.0 0 ratings

View Jamie D.

Enthusiastic Ivy League Tutor (for many subjects)

I am an Ivy League educated mechanical engineer (Bachelor of Science) with approximately 10 years off and on, of experience as an engineer as well. I am also a patient tutor, having tutored in Algebra with a high school student prior to signing up for WyzAnt. Hi everyone, I'm new to Wyzant but am a well-educated and patient young man, with prior experience. I am available for most technical subjects (including Math at all grade levels, as well as a few other disciplines). I believe that everyone can succeed at any subject if given the opportunity. I am a graduate of Columbia Univer [more]


Photo: Danny L.

Danny L.

Mechanical Engineering Tutor

Glastonbury, CT 06033

Will travel 20 miles

$45 per hour.

4.5 2 ratings

View Danny L.

Dedicated Tutor with 20 Years as Comp & Mech Engineer

I completed my BS and MS in Mechanical Engineering. Not only I took Statis but also many other related courses in the major. I can share my experience in many ways to help you succeed, not only on the subject but also career options for Mechanical Engineering and Computer Science. I have years of technical experience, both in school and in engineering industry. I went through years of technical courses including math, engineering, and computer science. I am a dedicated, responsible and patient teacher/tutor. I am also a caring person and a good listener. I believe any teacher-student relati [more]



Photo: Raghu R.

Raghu R.

Mechanical Engineering Tutor

Ridgefield, CT 06877

Will travel 12 miles

$70 per hour.

4.88 68 ratings

View Raghu R.

I make math easier to love with focus on fundamentals

I have a Master's degree in Mechanical Engineering from Oklahoma State University and a Bachelor's degree from Indian Institute of Technology, Madras, India in Mechanical Engineering. I did very well in both getting A grades. My undergraduate degree, from IIT, is a very prestigious degree worldwide since getting into this institute for this program is extremely competitive (just 1 % get in.) I scored very high in GRE in both plain and subject (Mech Engg) and received admission and financial assistance from two US Universities including Duke. [more]


Photo: Wen-Te W.

Wen-Te W.

Mechanical Engineering Tutor

Rocky Hill, CT 06067

Will travel 30 miles

$60 per hour.

4.25 4 ratings

View Wen-Te W.

Patient and Knowledgeable Math, Physics, Mechanical Engineering Tutor

I have a PHd from Carnegie Mellon University. I taught nonlinear dynamics in RPI. I taught vibration, stress analysis, etc in CMU. I have a PhD degree in mechanical engineering from Carnegie Mellon University. I have taught stress analysis, vibration, calculus, and nonlinear dynamical systems. I have tutoring experience, as well. The student I taught improved from a C in math and physics to an A in advanced AP physics and math. The student had good scores in math and physics in SAT, and was admitted as a direct dental student. ... [more]


Photo: Thomas R.

Thomas R.

Mechanical Engineering Tutor

Woodstock, CT 06281

Will travel 20 miles

$35 per hour.

4.83 6 ratings

View Thomas R.

Making STEM Great Again!

I have tutored some mechanical engineering as well as assisted one of the assistant professors at the University of Utah NROTC when teaching thermodynamics during the fall of 2011 and spring of 2012 (after graduation), respectfully. I graduated with a 3.38 GPA with a BS in Mechanical Engineering, and will submit my official transcript if requested. I do not feel I am qualified to teach some of the higher level mechanical engineering classes that I did not do well in school in, but for all others (including statics, thermodynamics, heat transfer, fluid mechanics, basic computer programming, bas [more]


Photo: Adam G.

Adam G.

Mechanical Engineering Tutor

Middletown, CT 06457

Will travel 30 miles

$50 per hour.

4.5 6 ratings

View Adam G.

Engineering and Mathematics Tutor

I have a B.S. in Mechanical Engineering with a specialization in Aerospace Technology and a secondary major in Mathematics. I excelled in all of my Major courses throughout college (GPA 3.9) and consistently tutored fellow students throughout my career as a student. Also, I have worked in industry as a Mechanical Engineer in various roles for nearly 3 years, and I apply Mechanical Engineering principles everyday in my work. My experience includes Design, Manufacturing, Testing, Cost Analysis, and R&D. I am extremely passionate about this topic, and I further my understanding of the field and m [more]


Photo: Andrew G.

Andrew G.

Mechanical Engineering Tutor

Branford, CT 06405

Will travel 30 miles

$70 per hour.

4.6 5 ratings

View Andrew G.

One-on-One Help with Algebra, Calculus, Physics

I have a Bachelor's Degree in Mechanical Engineering (BSME) from NYU Polytechnic School of Engineering. My grade point average there was a 3.109/4.000. I am comfortable teaching statics, dynamics, thermodynamics, heat transfer, fluid mechanics, mechanics of materials, circuit analysis, and other general engineering subjects. Hello! Nowadays, I work as a mechanical engineer at an aerospace firm but still accept new STEM students of all skill levels. I have published papers on molecular dynamics, nanomaterials, and bioengineering in several science journals. I started off with a liberal arts d [more]